IR Infrared Hub Repeater System 12V 1 Receiver 2 Emitter Remote Control Extender

IR Hub - Control Hidden AV Equipment - 12V Power Supply

Overview

Our IR system is suitable for use with all major brands of remote control including universal remote controls. It allows information gathered from IR receivers to be relayed to IR emitters to control and operate AV equipment (whether they are in an AV cupboard or another room). Up to 5 IR receivers and 12 IR emitters can be used with this hub to control up to 12 sources such as an amp, Blu-Ray player, DVD player, sky box, etc. Once installed it can be fixed into position using the supplied screws.

What's Included?

1 x IR Hub
1 x IR Receiver (3m Long)
1 x Dual IR Emitter (3m Long) - - for use with up to 2 sources
1 x 12V Power Supply - for IR Hub
Screws for mounting IR Hub
Self-adhesive tape underneath the IR receiver and IR emitters

Installation

Normally the IR hub would be located near to your AV equipment. There are six 3.5mm mono emitter sockets (as seen on the diagram above) to which up to six dual IR emitters can be connected, please search through our shop to find this product, single emitters are available too. Up to five IR receivers can be used with this hub by wiring them in parallel at the screw terminals. The screw terminals are labelled +12VDC, ground, status and signal, the IR receiver has the following wiring to the 3.5mm stereo plug, Signal is tip, ground is the ring and power is the sleeve. We recommend only extending the IR receiver cables up to 20 metres each. When only one IR receiver is being used, we recommend not exceeding 50 metres for the total cable length. IR receivers are available in our shop too, they come in pre-set lengths of 3 metres. To extend an IR receiver cable, a '3.5mm extension cable' should be used, alternatively you can make your own cable to a set length by using, CAT5 cable and 3.5mm stereo plug and socket connectors.

IR emitters should be positioned in front of, above, below or fixed on to the IR receiver on your source device and any signals fed to the emitter will be blasted out to enable control of your equipment.

IR receivers should be positioned in the room where you would like to control your equipment from. They will then pick up any IR commands sent from your remote control and relay them back to the hub.

Status LED

Some 12V IR receivers can be purchased which have a 'status LED'. This is simply an LED which is illuminated when the source equipment is switched on. The status LED can be swithced on and off using a 12 volt trigger found on some equipment, alternatively you could simply buy a gang socket into which all of your source equipment would plug, as well as the power supply for the status LED. When the source equipment is off, the status LED will be too.

Features and Specifications

IR Hub;

Compact Size - this device can be placed near to AV equipment.
Dimensions - 24mm (h) x 80mm (w) x 57mm (d)
12V DC Socket with LED indicator to power the device. 12V 200mA Power Supply Included.
12V DC Socket for the Status LED - Power Supply not included but can be purchased separately if required.
6 x IR emitter output connections (3.5mm mono sockets)
1 x 12V IR receiver input connection (3.5mm stereo socket). Can be used with many brands of IR receiver. Signal is tip, ground is the ring and power is the sleeve.
1 x Screw Terminals - For connection of up to 5 IR receivers, labelled +12VDC, ground, status and signal,

IR Receiver

CFL Friendly - This IR receiver works in most lighting environments, even areas with compact fluorescent lighting (CFL), e.g. energy saving bulbs.
IR Confirmation LED - This is to confirm that an IR command has been picked up from your remote control
Wide/Dual Band IR Receiver - The IR receiver picks up IR commands from many types of remote controls.
Self-adhesive tape underneath the IR receiver for quick and easy fixing to any flat surface.
Receive Frequency Range - 34 KHz to 60 KHz
Transmit Frequencies - 38 KHz & 56 KHz
Range - 40ft (12m) @ 38KHz, 25ft (8m) @ 56 KHz
Dimensions - 45mm (w) x 15mm (H) x 13mm (D)
Power - 12VDC, 30mA Max

To order more IR receivers, IR emitters and IR systems with cables included for extending IR receivers, search through our shop.

Troubleshooting when installing

Sometimes IR receivers struggle receiving/distinguishing commands due to infrared interference usually caused by TVs, fireplaces or direct sunlight. If the interference is extremely high in the area where the IR receiver is placed the blue IR confirmation LED may always be on. To reduce the interference to a manageable level, placing masking tape or paper over the IR receiver can help. Newer TVs may have an 'energy saving function' which when in use the TV can emit a lot of IR interference. Turning this function off can help dramatically.